1、功能说明
    USB HID 设备

2、使用环境

    软件开发环境：KEIL MDK-ARM 5.34
                  IAR EWARM 8.50.1

    硬件开发环境：
        N32H482系列：
        基于评估板N32H482ZEL7_STB V1.0开发
        N32H487系列：
        基于评估板N32H487ZEL7_EVB V1.1开发


3、使用说明
    描述相关模块配置方法；例如:时钟，I/O等 
         1. SystemClock：240MHz
		 2. USBClock: HSE 16MHz
         3. GPIO：KEY2 -- PA15
                  LED1 -- PA3
                  LED2 -- PB4
                  LED3 -- PA8


    描述Demo的测试步骤和现象 
         1. 编译后下载程序复位运行；
         2. 通过 USB 线连接 J62 USB 口，电脑识别出HID设备
         3. 点击按键KEY2， HID设备会通过IN端点发出按键信息
         4. 在PC端通过OUT端点向设备发送数据可以控制LED1~LED3的状态
            发送 0x01 0x00 LED1灭
            发送 0x01 0x01 LED1点亮
            发送 0x02 0x00 LED2灭
            发送 0x02 0x01 LED2点亮
            发送 0x03 0x00 LED3灭
            发送 0x03 0x01 LED3点亮


4、注意事项
    可通过修改宏定义 USE_USB_HS_IN_FS 或 USE_USB_HS_IN_HS 切换设备为全速模式或者高速模式；
    另外需要使用16MHz、19.2MHz、20MHz、24MHz、26MHz或32MHz外部晶体。

1. Function description
    USB HID device

2. Use environment
    Software development environment: KEIL MDK-ARM V5.34
                                      IAR EWARM 8.50.1

    Hardware development environment:
        N32H482 series:
        Developed based on the evaluation board N32H482ZEL7_STB V1.0
        N32H487 series:
        Developed based on the evaluation board N32H487ZEL7_EVB V1.1

3. Instructions for use
    Describe the configuration method of related modules; for example: clock, I/O, etc. 
        1. SystemClock：240MHz
		2. USBClock: HSE 16MHz
        3. GPIO：KEY2 -- PA15
                 LED1 -- PA3
                 LED2 -- PB4
                 LED3 -- PA8
    
    Describe the testing steps and phenomena of the Demo

        1. Download the program after compiling and reset it to run;
        2. Connect the J62 USB port via a USB cable, and the computer recognizes the HID device; 
        3. When click the button KEY2, the HID device will send a key message through the IN endpoint.
        4. Control the status of LED1 to LED3 by sending data to the device through the OUT endpoint on the PC
           Send 0x01 0x00 LED1 Off
           Send 0x01 0x01 LED1 Light
           Send 0x02 0x00 LED2 off
           Send 0x02 0x01 LED2 Light
           Send 0x03 0x00 LED3 off
           Send 0x03 0x01 LED3 to light up
        
4. Attention
    The device can be switched to Full-Speed mode or High-Speed mode by modify the macro definition USE_USB_HS_IN_FS or USE_USB_HS_IN_HS;
    In addition, external crystal of 16MHz, 19.2MHz, 20MHz, 24MHz, 26MHz or 32MHz is required.